Pipes and water supply
Low water pressure: what to check and who to call
A weak stream at one tap does not prove that the whole home has low water pressure. First find out which fixtures are affected, compare hot and cold water, and check your municipality’s service notices. A sudden building-wide change, visible leak, unusual water appearance or nearby electrical hazard calls for prompt help. These observations help identify the right contact; they are not a pressure test or a diagnosis.
Pressure is not the same as flow
Pressure is the force water exerts in the piping; flow is how much water passes a point over time. A blocked faucet aerator can produce a thin stream even when the building supply has not changed. An efficient new showerhead may release less water than an older one by design. Conversely, a supply change may be noticed at several fixtures. Feeling less water in the shower is a valid comfort complaint, but it is not a gauge reading.
Compare similar fixtures under similar conditions. Does the bathroom sink run normally when the kitchen tap seems weak? Was the problem present before a faucet was replaced? A rough container-filling comparison may help you describe a change, but it cannot establish the pressure: faucet design, flow restrictors, handle position and simultaneous water use affect it. A plumber can select a suitable measurement when the situation requires one. Do not borrow a universal “normal” number from another home.
Water may seem to slow when a washer, shower and outdoor hose are operating together. Repeat your observation when fewer fixtures are in use, without wasting water. Tell the person investigating whether the change occurs only during simultaneous use or even with one tap running. A repeated difference is useful information; it does not identify a defective pipe. If the pattern grows worse, arrange an assessment instead of experimenting with settings throughout the house.
Natural Resources Canada lists flow-rate limits for certain faucet and aerator products. Those product values explain why fixtures can deliver different streams. They do not provide a homeowner with a target building pressure, and they should not be used to judge a pressure regulator. The device’s own instructions matter when considering permitted maintenance.
Start with safety and the local context
If water is near a receptacle, electrical panel or powered appliance, stay clear of the wet area and seek appropriate emergency help. Do not touch wet electrical equipment. An active pipe leak, rapidly spreading damage or a sagging wet ceiling needs prompt attention. Limit water use and arrange professional help. If shutting water off is necessary, use only a shutoff you already know and can reach safely; never force a stuck or unfamiliar valve.
Water that is discoloured, smells unusual or is subject to a drinking-water notice needs the instructions of the relevant authority before you drink it or use a water-consuming appliance. A pressure change alone neither proves that water is safe nor shows that it is unsafe. Public notices and health instructions take priority over generic advice. Avoid opening piping, dismantling a water heater or accessing municipal equipment to explore a theory.
Write down when the problem began. If many fixtures changed abruptly and neighbours report the same issue, consult your municipal water-service alerts. The City of Montréal says maintenance work, valve or hydrant operations and a broken water main can temporarily lower pressure. It also identifies a service-line leak or an issue inside the building as possibilities. That page is specific to Montréal; other communities have their own notices, contact numbers and procedures.
When just one tap or shower seems weak
Compare hot and cold at that fixture, then test an ordinary tap elsewhere in the room and another elsewhere in the home. If the others are normal, a restriction may be near the affected fixture: its aerator, showerhead, supply hose, cartridge or another component. This is a list of possible locations, not a parts diagnosis. Recent installation work or visible particles may be worth mentioning, but neither proves where any debris came from.
Check a local outlet by its model
An accessible, removable aerator may be inspected following the manufacturer’s directions. Protect the finish and keep track of its small parts and seals. Stop if a fitting is seized, the fixture is damaged or the instructions are unclear. Our separate guide to deposits on faucets and showerheads covers a local buildup problem. Moen’s aerator guide shows why model identification matters: exposed, concealed and non-accessible outlets differ. Its instructions apply to the relevant Moen product, not every faucet. Repeatedly cleaning one outlet is unlikely to address a change affecting several fixtures.
What if only the toilet tank fills slowly while normal faucets still run well? That points your observations toward the toilet’s fill system or local supply. The slow-filling toilet tank guide explains that separate problem. Tank refill time by itself is not evidence that an entire house lacks pressure. If cold-water fixtures elsewhere also slow down, widen the investigation beyond the toilet.
For a weak shower stream, note the spray setting and whether a different fixture has changed. A new showerhead may feel different because of its design or installation. Follow its model-specific directions and seek help if needed. Do not remove a restrictor or alter an anti-scald feature simply to make the spray feel stronger. A visible drip at the shower or faucet is another symptom to report; it may need its own assessment rather than being treated as proof of a general pressure problem.
When several fixtures or the whole home are affected
Make a simple map of the symptom: which rooms and floors, whether hot and cold are both affected, and whether the issue remains when only one fixture is used. A whole-home change may involve the municipal supply, the building’s service line, an internal restriction, a leak or another component. The pattern helps narrow the investigation, but it cannot confirm one cause. Avoid replacing equipment solely because all taps seem weak.
Check the utility context first
Check the official alerts for the municipality serving the address. In Montréal, the City’s low-pressure page points residents to notices and alerts and to 311. Elsewhere, use that municipality’s own reporting channel. A neighbour’s observation can show that the issue may be shared, but it does not establish the cause, the extent or when service will return. Use an official advisory for drinking-water instructions, not a social-media post.
With no matching alert, record whether other units in the building have the problem. In an apartment or condominium, tell the owner or building manager; common plumbing and access arrangements differ from a detached home. Do not work on shared valves, a meter, a pressure regulator or a water service line to test a hypothesis. For an owner-occupied house, a plumber can evaluate persistent indoor symptoms after the municipal picture and simple fixture differences have been checked.
A new damp area, an unexplained sound of running water while fixtures are off, or growing water damage may warrant leak investigation. None confirms that a leak caused the low flow. Observe and document without opening a wall. The guide to possible hidden-water-leak signs handles that separate question. Active leakage deserves attention even if some taps still seem to run normally.
When hot water alone has poor flow
Compare hot and cold at more than one tap, taking care around potentially scalding water. If cold flow remains normal throughout the home, a building-wide municipal supply change is a less direct explanation of what you observe. A hot-water distribution issue, mixing valve, heater connection or a local faucet problem may deserve attention. Poor hot-water flow is different from having too little hot water available or water that does not reach the desired temperature.
Do not drain, adjust or dismantle a water heater to investigate flow. Hot water under pressure, electricity and gas equipment can be hazardous. If only one tap’s hot side seems weak, compare another hot outlet before calling it a whole-system problem. If every hot outlet is affected, tell the plumber or building manager. Mention leaks, unusual noises and temperature changes as observations. None by itself tells you which part to replace.
Sudden and gradual changes call for different questions
A sudden change makes the time line particularly important. Note an approximate start time and any recent outage, building work, fixture replacement, freeze event or visible leak. Then check municipal notices. A simultaneous event may be relevant without being the cause: nearby construction, for example, cannot be blamed from timing alone. If the water is also discoloured, follow the municipal quality guidance rather than running appliances to see if the condition clears.
A gradual decline may reflect a restriction developing over time, but it does not reveal its location or material. Compare fixtures and both temperatures. Think about whether a new water-saving device or a change in household use altered your impression. Pipe age is not a diagnostic test. Our guide to pipe lifespan and replacement decisions provides context without implying that older pipes must be the cause of this symptom.
Some changes recur at certain times rather than staying constant. Keep a short dated record: morning or evening, which outlets were in use, whether neighbours noticed anything and whether an official alert was posted. An intermittent issue still deserves assessment if it keeps returning. Do not run taps for long periods to create evidence. A short, safely recorded video can sometimes help show a difference between a normal and an abnormal stream.
A useful observation sequence that avoids adjustments
First look for an active leak or electrical danger. Then compare two or three ordinary taps in different rooms, testing hot and cold as safely as possible. Repeat when no large water use is underway. Note what changed since the last normal period and check municipal alerts. This sequence sorts the symptom into useful branches; it is not a technical test. You need not open a pipe or buy a gauge before making a call.
If a local shutoff was recently operated for planned work, tell the person who did the work. Do not force an old valve or turn a regulator to experiment. The right measurement depends on the installation and where and when it is taken. A fixture manufacturer may specify care for its own model, but instructions for one product do not automatically apply to every tap, valve or home. If you cannot safely identify a control, leave it for someone qualified to assess.
Tell the person you call if the home uses a private well, pump, pressure tank, water-treatment system or softener. Such equipment changes the relevant questions; a municipal network alert may have little bearing on a private supply. This guide focuses on ordinary homes connected to a water distribution system and does not provide pump, tank, filter or softener adjustments. The product manual and a professional familiar with that equipment become important in those situations.
Choosing the right first contact
Match the contact to the pattern
Shared or network-wide change: use the official service-alert and reporting channel of the water supplier for your address. In Montréal, the City refers residents to its alerts and 311. Other municipalities use their own contacts. Explain the street or area, the start time and whether hot and cold are both affected. If the municipality issues a drinking-water advisory, follow its specific directions until it changes or ends.
Rental or condominium building: report the issue to the owner or manager, especially when multiple units or common equipment may be involved. State plainly if there is a leak or immediate hazard. Occupants should not operate common valves or assume who owns a buried section of pipe. The manager can coordinate access and the appropriate utility or plumbing assessment. Keep a record of what you reported and when.
Persistent indoor problem: once you have checked notices and compared fixtures, a plumber can assess the building side. ProDrain’s residential plumbing page describes the broader service. When observations specifically raise a question about the private supply, read the water service line page for that separate scope. Weak flow does not automatically call for excavation or line replacement; assessment determines what work, if any, fits.
Make the first call useful
Give the person you call the address, building type, approximate start time, affected fixtures, hot-versus-cold difference, recent work, any alert and any leak. Describe what you observed rather than a confident cause. Ask what will be checked first, whether access to equipment is needed, how findings will be explained and which options depend on inspection. If damage is increasing, say so immediately to help them understand urgency.
For Montréal, the ProDrain contact number is 514 571-5072. For the South Shore, Laval and North Shore, it is 514 298-1911. These numbers provide a route to request an assessment, not a promise about diagnosis, method, price or arrival time. If the location is outside those stated areas, use the contact page to confirm routing.
What a professional assessment can clarify
The first task is to locate the change before recommending work. Depending on the building, the plumber may compare outlets systematically, examine fixtures, take an appropriate pressure reading, or inspect the indoor supply. Interpretation depends on the setup. A single reading taken at a quiet moment may not explain an intermittent problem; ask where and under what conditions it was taken. A symptom reported accurately saves time even when you do not know the technical term.
When the municipality confirms a network incident, restoration or a specific utility response may be the next step. Random private-plumbing adjustments could accomplish nothing. Conversely, an absence of a posted alert does not conclusively clear either the public or private side. The water utility and a plumber have different roles. Boundaries and reporting processes depend on the property and municipality; do not assume one rule covers every Greater Montréal address.
Ask what the proposed work will correct
If work is proposed, ask which finding supports it and what the work is expected to correct. An aerator, faucet cartridge, indoor pipe section, leak and buried service line are very different jobs. Materials and age may affect a repair choice, but they cannot diagnose low flow by themselves. The related guide to plumbing pipe materials and their uses explains material decisions without turning this symptom into a remote replacement recommendation.
After the issue is addressed, confirm what changed at the originally affected fixtures under ordinary use. Keep any measurements, photos and work description with your home records. If the symptom returns, note whether it has the same timing and hot/cold pattern. This follow-up helps distinguish a recurring local restriction from a new event. Do not assume that one successful repair guarantees every future change has the same cause.
Frequently asked questions
Why is just one faucet running slowly?
A local restriction, faucet aerator, cartridge or product design may explain it. Compare hot and cold at that faucet and another tap before concluding anything about the whole home. Follow the manufacturer’s care directions for an accessible removable aerator, and stop if a fitting resists. A persistent change or leak deserves assessment. The stream alone cannot identify a replacement part.
Does a weak shower prove low water pressure?
No. Showerhead design, spray mode and local buildup affect the amount of water you feel. Compare other fixtures and both temperatures. Comfort matters, but a shower sensation is not a pressure reading. Do not remove a flow device or alter anti-scald protection simply to increase the spray.
What should I do if every tap suddenly slows?
Check for immediate hazards or active leakage, then look at official municipal alerts. If it is easy to do so, ask whether nearby neighbours have noticed the same change. Record the start time and affected fixtures. Report a possible network issue through the local utility channel. If no alert fits or the problem persists in your building, contact the manager or a plumber. Follow any water-quality notice.
What if only the hot side has weak flow?
Compare hot and cold at more than one tap, avoiding scalding water. A single affected outlet can differ from a problem across the hot-water distribution. Tell the plumber which pattern you found. Do not open, drain or adjust the water heater to explore it. Weak hot-water flow is not the same symptom as running out of hot water.
Possible leaks, precautions and calling for help
Does low flow mean I have a hidden leak?
No. A leak is one possibility, especially when there are damp patches, unusual running-water sounds or growing damage. Those signs warrant investigation but do not confirm the cause of low flow. Promptly address active leakage. You do not need to open walls to report what you observed.
Should I adjust the regulator or main valve?
Do not adjust a pressure regulator or force a stuck or unknown valve to test a theory. Tell the professional about recent work and any controls you know were operated. If an active leak requires water to be shut off, use only a clearly identified shutoff that is safely accessible. Seek help when it is not.
Should I call the municipality or a plumber first?
For a sudden change affecting many fixtures, check the municipality’s notices and report through its local channel. For one fixture or a persistent indoor problem with no matching notice, contact the owner, manager or plumber as appropriate. Both utility and building-side investigation may be needed. The responsibility boundary should be established for the specific property and municipality.
What details should I have ready when I call?
Share the start time, affected rooms, hot-versus-cold pattern, whether use of other fixtures changes the result, recent work, any posted alert and any leak. Mention the building type and private water equipment if present. A description of observed facts is more useful than an unsupported diagnosis.
Sources and scope
The City of Montréal explains possible network and building causes and points residents to local alerts (updated July 27, 2021). Natural Resources Canada describes regulated flow rates for certain faucet and aerator products; those specifications are not household pressure readings (modified July 2, 2026). The City of Waterloo provides another municipal example of sorting low flow by fixture and hot-versus-cold pattern, but its reporting procedures do not apply in Québec. For an actual incident, follow the authority and product instructions relevant to your address and equipment.
